A shower tray only performs as well as the base beneath it. A tray that is even slightly unsupported, out of level or poorly connected to the waste can lead to movement, cracked grout, failed silicone and leaks below the floor. Knowing how to fit a shower tray properly means planning the waste route first, creating a fully supported base and leaving the final seal until the wall finish is in place.
This guide covers the typical installation of a low-profile acrylic, stone resin or mineral-cast tray on a solid floor. Always check the tray manufacturer's fitting instructions too. Requirements for bedding compounds, leg kits and waste access vary between products.
Before you fit a shower tray, check the room
Start by confirming that the tray size, enclosure and waste position work together. Measure the finished wall-to-wall space, not just the bare opening. Wall boards, tile adhesive and tiles all reduce the available room, which matters when fitting a close-fitting enclosure.
Check the floor for level and soundness. A concrete floor may need local levelling before the tray is installed. Timber floors need to be firm, with no bounce or loose boards. Repair damaged boards and strengthen the area where needed before adding weight from a tray, enclosure and user.
The waste needs particular attention. A low-profile tray often needs the waste and pipework recessed into the floor, or a route beneath a suspended timber floor. Make sure there is enough fall in the waste pipe towards the soil connection. For a raised tray, a panel or riser kit may provide the clearance needed for the trap and pipework.
Turn off water supplies if pipework is being altered. If there are electrical cables or underfloor heating beneath the fitting area, identify their position before cutting into the floor.
Tools and materials for fitting a shower tray
The exact materials depend on the tray and subfloor, but most installations need a spirit level, tape measure, pencil, drill, appropriate fixings, screwdriver, adjustable spanner and a utility knife. You will also need the correct shower waste, waste pipe and fittings, plus the tray manufacturer's recommended adhesive or bedding material.
For many solid-bed trays, a suitable cement-based tile adhesive or sand and cement mortar bed is used. Do not assume that expanding foam is an acceptable alternative. It can leave voids and allow movement unless the manufacturer specifically permits it. For trays supplied with adjustable legs, use the supplied frame and fixings rather than improvising a support system.
Have sanitary silicone ready for the final stage, but do not use it to make up for an uneven wall, a rocking tray or poor plumbing. Silicone is a flexible finishing seal, not a structural fixing.
How to fit a shower tray on a solid bed
1. Dry-fit the tray and mark the waste
Place the tray in position without adhesive. Check that it sits in the intended orientation and that the enclosure will have suitable fixing surfaces on both walls. Mark around the tray if helpful, then mark the waste location accurately.
Remove the tray and cut or form the recess for the waste and pipework if required. Keep enough room to connect and, where possible, inspect the trap. On a concrete floor, avoid unnecessary deep cuts that may affect the slab. If access from below is not possible, a riser kit can be the more practical choice.
2. Connect the waste carefully
Fit the waste body to the tray following the supplied instructions. Seals must be clean, correctly seated and tightened evenly. Over-tightening can distort plastic components or damage seals, while an under-tightened fitting may leak.
Connect the waste pipe with the correct fall. The pipe should be supported rather than hanging under its own weight. Before bedding the tray, carry out a dry check to make sure the waste aligns naturally and the tray can settle into its final position without forcing the pipework sideways.
3. Prepare a full, supportive bed
Vacuum dust and loose debris from the floor. If using a mortar or adhesive bed, mix only enough for the working time stated by the product manufacturer. Spread it across the whole footprint where the tray needs support, not as a few isolated blobs.
Full contact matters because a tray flexes when weight is concentrated underfoot. Unsupported areas can eventually cause creaking, cracking or failure at the wall seal. Keep bedding material clear of the waste opening and any planned access point.
4. Set the tray level
Lower the tray gently into the bed, ensuring the waste connection remains correctly aligned. Use a long spirit level across the tray in several directions. The tray itself should be level, even though its internal surface is designed to direct water towards the waste.
Press the tray down evenly until it is fully supported. Do not stand heavily in one corner to force it into position. Recheck the level and adjust immediately while the bedding material is workable. Wipe away excess material around the edges before it hardens.
5. Test the waste before closing access
Once the tray is stable, pour water into the tray and check that it drains freely. Inspect the waste connection from below or through the access opening. A tissue held around joints can reveal a small leak more clearly than a quick visual check.
Do not fit the enclosure, tile walls or permanently close the access panel until the waste has been tested. Correcting a connection at this stage is straightforward. Correcting it after a tiled bathroom is complete is not.
Fitting a shower tray with adjustable legs
Raised trays are fitted differently, but the same principles apply. Assemble the frame and legs exactly as instructed, then position the tray and adjust each leg until the tray is level and fully supported. The central legs are just as important as those at the corners.
Fix the frame or legs to the floor where the manufacturer requires it. Connect and test the waste before fitting the front panel. A removable panel, or another planned access route, is essential if the trap cannot be reached from below. Never bury a waste connection where it cannot be inspected or serviced.
Tile and seal in the right order
The usual sequence is to install the tray first, then fit waterproof wall backing and tile down to the tray edge. This allows the finished wall surface to overlap the tray, helping water run back into the shower area rather than behind it.
Do not grout the joint between wall tiles and the shower tray. This junction moves slightly in normal use and needs a flexible sanitary silicone seal. Allow adhesive and grout to cure first, then clean and dry the joint thoroughly. Apply silicone in a consistent bead, smoothing it neatly so it bonds to both surfaces.
Many fitters fill the tray with water before sealing. The slight load can help the seal accommodate normal movement. Follow the silicone manufacturer's curing guidance before using the shower, and ensure the room is dry and well ventilated while it cures.
Common fitting mistakes to avoid
The most costly errors tend to happen before the tray is visible as part of the finished bathroom. Avoid these four problems:
- Bedding a solid tray on small dabs of adhesive rather than full support.
- Installing the tray before checking that the waste has adequate fall and access.
- Assuming a tray should slope towards the drain when the tray must actually be level.
- Sealing the tray to bare walls, then trying to tile over or around an awkward silicone joint.
It is also worth checking enclosure instructions before drilling. Some enclosures need a specific clearance from the tray edge, and a slightly oversized tile trim or uneven wall can affect how the door closes.
A well-fitted shower tray gives every finish above it a better chance of lasting: the enclosure sits true, tile joints stay tidy and water goes where it should. Plan the support, waste and tile build-up before opening the adhesive, then take time to test the drainage before the final seal is applied.

